4+1 SATA II 300 IDE/PATA PCI-E
Combo Host Card w/ RAID & Port
Multiplier
User Manual
Model: UGT-IS100R
All brand names and trademarks are properties of their respective owners.
w w w . v a n t e c u s a . c o m
Features and Benefits
z
z
z
z
z
z
Compliant with one-lane 2.5Gb/s PCI Express specification
Compliant with Serial ATA 1.0 specification
Supports Serial ATA Generation 2 transfer rate of 3.0Gb/s
Supports Native Command Queue (NCQ) on SATA ports
Supports Hot Plug
Provides three independent channels to connect two SATA
and two IDE/PATA devices
z
z
z
Supports up to UDMA6 transfer mode of IDE/PATA
Supports up to 4 storage device connection
Supports RAID 0, 1, 0+1, JBOD, Individual Mode
Bus Interface
z
PCI-Express x 1
Ports
z
z
z
2 x internal SATA Ports
2 x external (eSATA) Ports
1 x IDE/PATA Port
UGT-IS100R
Page 3
System Requirements
z
PCI Express-enabled system with one available PCI
Express slot
z
Windows® 2000, XP/2003/Vista/2008/7 (32/64 bit)
Package Contents
z
1 x 4+1 SATA II 300 IDE/PATA PCI-E Combo Host Card w/
RAID & Port Multiplier
z
z
z
z
1 x Driver CD
1 x User’s Manual
2 x SATA Data Cable
1 x IDE/PATA Cable
Hardware Description
Note: There are four SATA ports in 4+1 SATA II 300 IDE/PATA
PCI-E Combo Host Card w/ RAID & Port Multiplier . We name
these ports CON1 to CON4. Ports CON3 & CON4 are external
SATA ports and CON1 & CON2 are internal SATA ports. By
changing the jumper setting on the 4+1 SATA II 300 IDE/PATA
PCI-E Combo Host Card w/ RAID & Port Multiplier that allows
you to select between external and internal ports to use. By
UGT-IS100R
Page 4
default, Port CON1 & CON2 are working.
Jumper Settings
JP
Description
1-2 close
Active Port
J1-J4
Enable
SATA
Port
Port
CON1
2-3 close
Enable
SATA
UGT-IS100R
Page 5
CON3
Enable
CON2
Enable
CON4
J5-J8
1-2 close
2-3 close
SATA
SATA
Port
Port
Hardware Installation
1. Turn Off the power to your computer.
2. Unplug the power cord and remove your computer’s cover.
3. Remove the slot bracket from an available PCI-E slot.
4. To install the bard, carefully align the card’s bus connector
with the selected PCI-E slot on the motherboard. Push the
board down firmly.
5. Attach your internal or external devices to the 4+1 SATA II
300 IDE/PATA PCI-E Combo Host Card w/ RAID & Port
Multiplier .
6. Replace the slot bracket’s holding screw to secure the card.
7. Replace the computer cover and reconnect the power cord.
UGT-IS100R
Page 6
RAID Arrays
RAID Arrays are setup in the 4+1 SATA II 300 IDE/PATA PCI-E
Combo Host Card w/ RAID & Port Multiplier ’s BIOS.
There are four configurations supported:
RAID level/Type Configurations
Number
of
disks
needed
RAID 0
Disk Striping
Disk Mirroring
Disk Striping
2 or 3 or 4
RAID 1
2
4
RAID 0+1
+
Mirroring
JBOD
Disk Concatenation 2 or 3 or 4
RAID 0 (Striping)
1. As the BIOS boots press Ctrl+J when prompted to enter the
RAID BIOS.
2. At the next screen select Create RAID Disk Drive, press
Enter.
3. Enter RAID name, press Enter.
4. Please use arrow keys ↑ and ↓to switch the RAID level to
0-Stripe, then press Enter.
5. Please use arrow keys ↑ and ↓to switch the disk, use the
UGT-IS100R
Page 7
“space” key to mark the selected disk, then press Enter.
6. Please use arrow keys ↑ and ↓ to select chunk size from 4K,
8K, 16K, 32K, 64K or 128K, then press Enter.
7. Input the RAID size, press Enter.
8. When asked Created RAID on the select HDD (Y/N)?,
press Y to accept.
9. At the next screen select Save And Exit Setup, press
Enter. When asked Save to disk &Exit (Y/N)?, press Y to
exit the BIOS.
RAID 1 (Mirroring)
1. As the BIOS boots press Ctrl+J when prompted to enter the
RAID BIOS.
2. At the next screen select Create RAID Disk Drive, press
Enter.
3. Enter RAID name, press Enter.
4. Please use arrow keys ↑ and ↓to switch the RAID level to
1-Mirror, then press Enter.
5. Please use arrow keys ↑ and ↓to switch the disk, use the
“space” key to mark the selected disk, then press Enter.
6. Input the RAID size, press Enter.
UGT-IS100R
Page 8
7. When asked Created RAID on the select HDD (Y/N)?,
press Y to accept.
8. At the next screen select Save And Exit Setup, press
Enter. When asked Save to disk &Exit (Y/N)?, press Y to
exit the BIOS.
CONCATENATION (JBOD)
1. As the BIOS boots press Ctrl+J when prompted to enter the
RAID BIOS.
2. At the next screen select Create RAID Disk Drive, press
Enter.
3. Enter RAID name, press Enter.
4. Please use arrow keys ↑ and ↓to switch the RAID level to
JBOD-Concatenate, then press Enter.
5. Please use arrow keys ↑ and ↓to switch the disk, use the
“space” key to mark the selected disk, then press Enter.
6. Input the RAID size, press Enter.
7. When asked Created RAID on the select HDD (Y/N)?,
press Y to accept.
8. At the next screen select Save And Exit Setup, press
Enter. When asked Save to disk &Exit (Y/N)?, press Y to
UGT-IS100R
Page 9
exit the BIOS.
RAID 0+1 (Striping + Mirroring)
1. As the BIOS boots press Ctrl+J when prompted to enter the
RAID BIOS.
2. At the next screen select Create RAID Disk Drive, press
Enter.
3. Enter RAID name, press Enter.
4. Please use arrow keys ↑ and ↓to switch the RAID level to
01-Stripe+Mirror, then press Enter.
5. Please use arrow keys ↑ and ↓ to select chunk size from 4K,
8K, 16K, 32K, 64K or 128K, then press Enter.
6. Input the RAID size, press Enter.
7. When asked Created RAID on the select HDD (Y/N)?,
press Y to accept.
8. At the next screen select Save And Exit Setup, press
Enter. When asked Save to disk &Exit (Y/N)?, press Y to
exit the BIOS.
UGT-IS100R
Page 10
Delete RAID Disk Drive
1. As the BIOS boots press Ctrl+J when prompted to enter the
RAID BIOS.
2. At the next screen select Delete RAID Disk Drive, press
Enter.
3. Please use arrow keys ↑ and ↓to select the array you want to
delete, use the “space” key to mark the selected array, then
press DEL.
4. When asked ALL DATA ON THE RAID WILL LOST!! ARE
YOU SURE TO DELETE (Y/N), press Y to accept.
Solve Mirror Conflict
When a RAID set is created, then metadata written to the disk
includes drive connection information. If, after a disk failure, the
replacement disk was previously part of a RAID set (or used in
another system), it may have conflicting metadata. If so, this will
prohibit the RAID set from being either created or rebuilt, in order
for the RAID set to function properly, this old metadata must be
first overwritten with the new metadata. To resolve this, from the
main BIOS window select Solve Mirror Conflict, then press
Enter, the correct metadata, including the correct drive
UGT-IS100R
Page 11
connection information, will be written to the replacement disk.
Rebuild Mirror Drive
When a failure to one member occurs, you will be notified by the
RAID BIOS during boot. The steps below will guide you in
rebuilding a failed mirror set.
1. Replace the failed drive(s) with one of equal or greater
capacity, start the computer.
2. During boot press Ctrl+J to enter the RAID BIOS.
3. Select Rebuild Mirror Drive press Enter.
4. Please use arrow keys ↑ and ↓to select the array you want to
rebuild, press Enter.
5. Please use arrow keys ↑ and ↓to select the destination disk,
press Enter.
6. When rebuilding is finished, select Save And Exit Setup,
press Enter. When asked Save to disk &Exit (Y/N)?, press
Y to exit the BIOS.
BIOS Configuration
The 4+1 SATA II 300 IDE/PATA PCI-E Combo Host Card w/ RAID
& Port Multiplier BIOS will appear every time your system starts
UGT-IS100R
Page 12
up. During this (POST) process, the BIOS will show up and
indicate the devices attached to it.
Driver Installation
For Windows® 2000, XP and Server 2003
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents of
the “UGT-IS100R\2000_XP_2003_Vista\Floppy32” folder,
found on the driver CD, onto a blank floppy disk then follow
the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press F6 to install the RAID
driver.
4. When prompted, press S to specify the location of the driver.
5. Insert the floppy disk, then press Enter.
6. Select (Windows 2000) RAID Driver for JMicron JMB363
Controller or (Windows XP/2003) RAID/AHCI Driver for
JMicron JMB36X Controller, then press Enter.
7. Press Enter to finish driver installation, then follow the
UGT-IS100R
Page 13
on-screen instructions to complete the Windows installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. Please insert the CD driver bound with 4+1 SATA II 300
IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier
into your CD-ROM Drive.
3. At the Windows desktop, click Start, then Run.
4. Type D:\UGT-IS100R\2000_XP_2003_Vista\setup.exe, click
OK. (Change D:\ to match your CD-ROM drive letter)
5. Follow the on-screen instructions to complete the
installation.
6. Restart Windows to complete the installation.
For Windows® XP-x64/Server 2003-x64
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents of
the “UGT-IS100R\XP_2003_Vista\Floppy64” folder, found
on the driver CD, onto a blank floppy disk then follow the
UGT-IS100R
Page 14
directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press F6 to install the driver.
4. When prompted, press S to specify the location of the driver.
5. Insert the floppy disk, then press Enter.
6. Select (Windows XP/2003 x64) RAID/AHCI Driver for
JMicron JMB36X Controller, then press Enter.
7. Press Enter to finish driver installation, then follow the
on-screen instructions to complete the Windows installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. Please insert the CD driver bound with 4+1 SATA II 300
IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier
into your CD-ROM Drive.
3. At the Windows desktop, click Start, then Run.
4. Type D:\UGT-IS100R\XP_2003_Vista\setup.exe, click OK.
(Change D:\ to match your CD-ROM drive letter)
5. Follow the on-screen instructions to complete the
UGT-IS100R
Page 15
installation.
6. Restart Windows to complete the installation.
For Windows® Vista
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents of
the “UGT-IS100R\2000_XP_2003_Vista\Floppy32” folder,
found on the driver CD, onto a blank floppy disk then follow
the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press Load Driver to install
the driver.
4. Insert the floppy disk, please select JMicron JMB36X
Controller (A:\jRAID_f.inf), then press Next. (Change A:\
to match your floppy drive letter)
5. Follow the on-screen instructions to complete the Windows
installation.
For An Existing Installation
UGT-IS100R
Page 16
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. Please insert the CD driver bound with 4+1 SATA II 300
IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier
into your CD-ROM Drive.
3. At the Windows desktop, click Start, then Run.
4. Type D:\UGT-IS100R\2000_XP_2003_Vista\setup.exe, click
OK. (Change D:\ to match your CD-ROM drive letter)
5. Follow the on-screen instructions to complete the
installation.
6. Restart Windows to complete the installation.
For Windows® Vista-x64
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents of
the “UGT-IS100R\XP_2003_Vista\Floppy64” folder, found
on the driver CD, onto a blank floppy disk then follow the
directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
UGT-IS100R
Page 17
3. At the Windows Setup screen, press Load Driver to install
the RAID driver.
4. Insert the floppy disk, please select JMicron JMB36X
Controller (A:\jRAID_f.inf), then press Next. (Change A:\
to match your floppy drive letter)
5. Follow the on-screen instructions to complete the Windows
installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. Please insert the CD driver bound with 4+1 SATA II 300
IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier
into your CD-ROM Drive.
3. At the Windows desktop, click Start, then Run.
4. Type D:\UGT-IS100R\XP_2003_Vista\setup.exe, click OK.
(Change D:\ to match your CD-ROM drive letter)
5. Follow the on-screen instructions to complete the
installation.
6. Restart Windows to complete the installation.
UGT-IS100R
Page 18
For Windows® Server 2008/7 (32-bit)
For New Installation
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press Load Driver to install
the RAID driver.
4. Please insert the CD driver bound with 4+1 SATA II 300
IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier
into your CD-ROM Drive, click Browse.
5. Click on the Plus (+) sign next to the CD-ROM Drive, double
click the “UGT-IS100R\2000_XP_2003_Vista\Floppy32”
folder, then click OK.
6. Select JMicron JMB36X Controller, then press Next.
7. Follow the on-screen instructions to complete the
installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. Please insert the CD driver bound with 4+1 SATA II 300
IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier
UGT-IS100R
Page 19
into your CD-ROM Drive.
3. At the Windows desktop, click Start, then Run.
4. Type D:\UGT-IS100R\2000_XP_2003_Vista\setup.exe, click
OK. (Change D:\ to match your CD-ROM drive letter)
5. Follow the on-screen instructions to complete the
installation.
6. Restart Windows to complete the installation.
For Windows® Server 2008/7 (64-bit)
For New Installation
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press Load Driver to install
the RAID driver.
4. Please insert the CD driver bound with 4+1 SATA II 300
IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier
into your CD-ROM Drive, click Browse.
5. Click on the Plus (+) sign next to the CD-ROM Drive, double
click the “UGT-IS100R\XP_2003_Vista\Floppy64” folder,
then click OK.
6. Select JMicron JMB36X Controller, then press Next.
UGT-IS100R
Page 20
7. Follow the on-screen instructions to complete the
installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. Please insert the CD driver bound with 4+1 SATA II 300
IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier
into your CD-ROM Drive.
3. At the Windows desktop, click Start, then Run.
4. Type D:\UGT-IS100R\XP_2003_Vista\setup.exe, click OK.
(Change D:\ to match your CD-ROM drive letter)
5. Follow the on-screen instructions to complete the
installation.
6. Restart Windows to complete the installation.
To Verify Driver Installation
1. Right click My Computer and click Manage.
2. Select Device Manager.
3. Look for the following:
Windows® 2000/XP/2003: Double click SCSI and RAID
UGT-IS100R
Page 21
Controller:
-JMicron JMB36X Controller should be displayed
Windows® Vista: Double click Storage controllers:
-JMicron JMB36X Controller should be displayed
UGT-IS100R
Page 22
|
